Skip to main content

How to use Audio DSP on Antenna Analyzer (Features included after CEC V0.5)

How to use Audio DSP on Antenna Analyzer (Features included after CEC V0.5)


Audio DSP is a function that filters the sound coming from the transceiver into a desired range.

You do not need any hardware changes to use this feature. Just prepare your headphones. If you want to make a little bit better, you can add a very small $ 1 speaker to your board.

I am preparing to distribute the test firmware (V0.52). Please wait 1 ~ 2 days.

1.Required Hardware
EU1KY AA and Headphone.



The STM32F746 board has two sound inputs. However, Mic Jack is already using the EU1KY RF board.


Another sound input method of the STM32F746 is two microphones mounted on the board.

I use only one of the two microphones. (Right)
Put AA near the transceiver speaker and plug your headphone into the phone jack and you're all set.



Or you can install a small speaker as shown below.

You could easily get a small speaker around you. It can be extracted from malfunctioning headphone, earphone, mobile phone.
The speakers I used are below.
https://www.aliexpress.com/item/2pcs-1W8ohm-MP3-MP4-small-horn-Ramos-v2-0-10-15-oval-speaker-W10/32779312057.html?spm


2.How to use

Below is a picture of my development board.  I put a very small speaker on Mic for testing.
On the main screen, touch 'Audo DSP' button.


If you turn on your transceiver, you will probably see fft spectrum and waterfall graphs as shown below.
In the first run, it operates in 'Pass Through' mode.

May be too loud, so make sure the volume of the transceiver is very small in 'Pass through' mode.



Touch the desired filter button.
If you are filtering a fairly narrow area, please select BPF.
BPF supports 50Hz, 100Hz and 150Hz filtering.
Continue to touch the BPF button to change the filtering bandwidth.

Touch the red squares (B) below to move the center frequency.
The yellow squares(A) is the area to adjust the bandwidth in User Filter mode.

Move the center frequency to the area you want to hear.
If you hear a small noise when moving to the area you want to hear, increase the volume of the transceiver.
Since most of the other areas are removed, if you raise the volume, you will hear what you want to qso. Volume control is important.


If you have selected User Filter, you can select the range you want to hear by dragging the L and R areas below.



Since the center frequency is maintained even if you touch the BPF and the User filter alternately, it can be used alternately according to the communication status.


3.Test Video
Please refer to the video below for an example of use.



Thank you for reading
Ian KD8CEC

Comments

  1. Hello Ian,
    Next version will be receiver and final version will be all band transceiver? :-)

    ReplyDelete
    Replies
    1. Mirek
      It is wonderful. However, it seems to be difficult to structure the circuit.

      I am not an active ham. So I just use the antenna analyzer once or twice a month.
      Most of the time, the antenna analyzer is left on the desk.
      So I'm adding a few minor features.

      Ian KD8CEC

      Delete
  2. Can't we use the Audio In Jack, to which I and V outputs of the RF board of EU1KY VNA is connected ? We can directly connect the Headphone out of our Rig to the VNA and get the output from the Speaker out ? Using Microphone would pick up sound from the Shack.

    ReplyDelete
    Replies
    1. VU3ECN

      We can not use Audio IN Jack. So we have to use a microphone attached to the board. It would be useful to place AA near the speaker of the transceiver.
      Or add a small speaker like me.

      I'm considering building a HAM tool that will consist of less than $ 60.
      This would be a structure consisting only of the STM32F746 board and the SI5351 board.
      The Si5351 board will be available for $ 3 on eBay.
      I will be porting most of the features I have implemented in AA.

      At this time, you can use Audio In Jack of STM32F746 board, so you can connect to the transceiver directly.

      But I still considering it.

      Ian KD8CEC

      Delete
    2. Hi Ian,
      pardon my lack of knowledge about the Disco Board. Since such a device is better as dedicated one, what you propose would be a welcome thing. Would be looking for update from you. BTW, I have sent the order for the modified PCB for the VNA. I would send you a piece after testing it.

      Delete
  3. KD8CEC
    Have a Si5351A board with the
    Discovery Board V1.01 Antenna
    Analyzer
    Want to know if adding a TCXO
    with better than 0.5ppm over Temp
    might improve FT8 and WSPR
    Notice on FT8 unit moves around
    in frequency and with WSJT looking
    at waterfall see many signals evenly
    spaced about Center Carrier on 14.074MHz FT8
    Suspect the DC to DC converter
    is modulating the Si5351A or other
    device to cause spurs
    E-mail me at wb6dji_dx(at)icloud(dot)com
    Mike

    ReplyDelete
    Replies
    1. Ian
      Thanks in advance for any help
      Trying to enhance the
      Si5351A add on board for
      Improved FT8 operation
      Mike
      WB6DJI

      Delete
  4. It is my pleasure to read this wonderful blog of yours. Thank you so much for sharing. Porch Screening Port Charlotte, FL

    ReplyDelete

Post a Comment

Popular posts from this blog

Introduction to UV-K5 HF Fullband receive version 0.3

Introduction to UV-K5 HF Fullband receive Version 0.3 This is an introduction to UV-K5 HF full-band reception firmware 0.3HF using SI4732-A10. This version is released separately from the existing UV-K5 CEC firmware version. because space is needed to store a large PATCH file to use SI4732-A10's SSB. 0.3HF added several functions to use SSB for shortwave radio and amateur radio.

Release CEC Firmware v1.200 for uBITX All version(include V2, V3, V4, V5)

Release CEC Firmware v1.200 for uBITX All Version (include v2, v3, v4, v5) I did the firmware work for v5 when uBITX V5 was released, but I release it now. I received the feedback from a thankful beta tester and tested it myself by converting my uBITX v3 to v5 but I was not sure. I ordered the uBITX V5 and delivered the correct uBITX V5, so I made a little more fine-tuning. If you use V2, V3, V4, you do not need to update this firmware.

Introducing UV-K5 Version 0.1P (CW)

  Introducing UV-K5 Version 0.1P (CW Mode) CW-related functions have been added to version 0.1P. The spectrum function has been removed but is maintained in the source code. Later, when the source code is distributed, you can activate it and use it if necessary. This version is for testing purposes only. It will be redistributed as the stable version 0.2 in approximately 1-2 weeks. If you don't want to beta test, you can wait a week or two and download 0.2