Introduction to UV-K5 HF Fullband receive Version 0.41 (Changed from 0.40)
This is an introduction to UV-K5 HF full-band reception firmware 0.4HF using SI4732-A10.
This version is released separately from the existing UV-K5 CEC firmware version. because space is needed to store a large PATCH file to use SI4732-A10's SSB.
0.4HF added several functions to use SSB for shortwave radio and amateur radio.
0. About This Version
Changed in Version 0.41
- Version 0.40의 BandWidth Bug Fix
- Change CW Bandwidth to selectable (operates independently from SSB Bandwidth)
- When moving the band, the settings are saved in EEProm.
---------------------------------------------------------------
Version 0.4 is just a few simple features added to Version 0.3.
For basic usage instructions, please click the link below (Version 0.3).
This document only describes features added in 0.4.
Q&A 1: Will existing U/V radio functionality be maintained?
Yes, 16Mhz ~ 1200Mhz TX/RX and SSB Receive. Most features are retained.
Q&A 2 : Is SSB transmission possible?
It's not possible. Of course, if you transmit via FM, it will be received by an SSB radio. (Up or down frequency by about 1~2Khz) This is not SSB. This is reception by parasitic waves from FM. In this way, you can also listen to AM radio on an old SSB transmitter.
1. Band Plan
The number of bands changed from 23 to 20.
The last used frequency is saved for each band.
It is saved when you press the Exit button in HF reception mode to exit, so if you want to save the last information, press the 'Exit' button to exit.
In HF reception mode, briefly press keypad 0.
If you press '0' again, the next page will be printed. In the case of a band that includes the current frequency, it is inverted as shown below.
In the band plan, press the number button on the far left to move to the corresponding band.
When the 'HF Dual' mode is in operation, the 'DUAL RX RESPOND' mode of the U/V radio does not operate.
If you press '0' again, the band plan will disappear.
Video with Version 0.4HF
2. Dual Receive
Performs HF reception and V/U reception simultaneously.
Change 'HF Dual' to 'On' in the menu.
Caution : If the value of HFDual changes, be sure to turn off and turn on UV-K5.
Switch to HF reception mode.
Press the Exit button to return to U/V radio mode.
HF reception will continue.
You can adjust the HF reception volume in the HFDVol (HF Dual Volume) menu.
This is the same function as the BAL (Balance) menu found in high-end handy radios from Kenwood or Icom.
3. BFO Value
Apply the BFO value to SI4732-A10 in reverse from Version 0.4
You can use the BFO value in Hz (below 1Khz).
If Current Frequency is 14.074 and BFO is 250 then 14.074250Mhz
4.Other
Save settings (when pressing the Exit button)
Enable channel scan high-speed mode.
Fixed bug related to LNA settings
For functions that do not require Up/Down (Mode, LNA and ETC), the Up and Down buttons operate identically. (Secure program space)
5.Download
Download and use CEC_041.HF.packed.bin from the link below.
Hello CEC, this is BG4QL. The problem of intermittent sound when adjusting the BFO in version 0.41 still exists. In version 0.3, the BFO can be adjusted smoothly, which makes it very convenient to adjust + or - according to the pitch of the sound. This is the video I received in 0.3 https://www.bilibili.com/video/BV1SZ42187sb/?vd_source=c26d953b78685bf7f0da8f14683f586f. The effect is very good. I can judge the + or - of the BFO by the pitch.
ReplyDeleteWhat about the CW transmitting feature in this version please?
ReplyDeletehi！ SSB sound is very small, is the program still need to be modified, 4732ssb mode, the program limits the sound is not turned on to the maximum?
ReplyDeleteplease add support for m24m02 memory
ReplyDeleteDid the hardware mod using the board from aliexpress. Seems to work good but I am not sure why they ask to replace the choke at the antenna input for another value. I think they supply a 100 uh rf axial choke. Correct me if I am wrong. Non of the modes posted here hask for that. Anybody knows? Also I find the audio output on USB and LSB way lower then on AM mode. Is this normal? Otherwise fantastic work. I am super impressed with the mods.
ReplyDeleteIts a 1mH inductor, gives you a huge improvement in receiving lower bands like 600khz am stations etc.
DeleteThanks, I was pretty sure on 1mh but the colors are not that good, but figured it must have been about that. Thanks for comfirming that and yes the lower frequencies are pretty good in reception, rivals my Malahit DSP receiver.
DeleteJust a not on .41, the STP does not work in FM mode, if you use the side buttons to move the cursor, it just exits to the VHF page.
ReplyDeletePlease add support for chirp!
ReplyDeleteTX Power Output Drops with 1/3 after installing this firmware compared to IJV 3.0
ReplyDeleteThank you for enlightening me; I was unaware of this information before. find here
ReplyDeleteHello! In the new firmware version you can change the parameter "Property 0x3103. AM_AUTOMATIC_VOLUME_CONTROL_MAX_GAIN" to 48 dB. This will improve SSB reception. And please disable the S-meter update, a fairly loud click is heard when receiving.
ReplyDeleteHas anybody installed and tested this new board released on Ali including audio amplifier ? If so, is there a need for any other modifications rather than replacing the current chip ?
ReplyDeleteLink to the new board on Ali. related to my above - https://www.aliexpress.com/item/1005006848009481.html?spm=a2g0o.cart.0.0.6c5538daoW0Lu0&mp=1
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteHello! I bought a kit with black PCB for UV-K5 (8), SMD components and 2 megabits memory chip. Unfortunately, I don't have any diagrams, and modified software too. Can I ask you about this?
ReplyDeletehttps://a.aliexpress.com/_Eyn1KFd
P.S. Chip EEPROM M24M02
DeleteIch habe das Problem das ich immer wieder , wenn ich die Taste 0 gedrückt halte und dann im Display nur noch Wait steht.
ReplyDeleteich habe den Lusya modification modul einschl ießlich si4732 chip und kristall oszillator teile für quan sheng UV-K5 installiert
https://drive.google.com/file/d/1PsEqBSLvNJU0jdlPTXeifYdeqDQVOTrX/view?usp=sharing
ReplyDeleteWait Problem :(
ReplyDeleteCorporate video services encompass a range of offerings provided by specialized companies or professionals. These services include video production, editing, scriptwriting, filming, animation, voiceover, post-production, and distribution. They cater to businesses seeking high-quality video content for promotional, educational, or internal purposes. Companies offering corporate video services tailor their offerings to meet their clients' specific needs and objectives.
https://www.toolbox-studio.com/corporate-videos
Awesome post! Thanks for the share. Polished concrete floor installers
ReplyDeleteI'm curious to know more about the specific features added in versions 0.1 to 0.71. Could you elaborate on the most significant improvements?
ReplyDeletecommercial window cleaning cincinnati ohio
This is nice. I love the content of this blog. rescreening
ReplyDeleteFantastic! This version is released for El Paso Drywall Contractors separately from the existing UV-K5 CEC firmware version.
ReplyDeleteGlad to visit this site. It's informative one. Builders Crack Alternative
ReplyDeleteInteresting post! Thanks for the update. pool enclosure
ReplyDeleteFor those who prefer to utilize AA exclusively for instrumentation, I have divided the Version into 1.01 and 1.0A. Check this retaining wall!
ReplyDeleteInteresting. I'll check it out!
DeleteRegards,
AEGIS Business Directory
Bookmarked. Kindly also visit my web site =). We may have a hyperlink exchange contract among us. Red Deer Roofing
ReplyDeleteIt's great to check this awesome post. Fence company
ReplyDeleteThis is awesome! Glad to visit this site for an informative content. concrete slab
ReplyDeleteI normally want high-quality web content, and also this thing I found this in your post. It is advantageous and considerable for us. Maintain sharing these types of posts, Thanks. roxtec
ReplyDelete