Skip to main content

Release CEC Firmware v1.121 for uBITX V5

Release CEC Firmware v1.121 for uBITX V5

I did some experiments with the help of a beta tester with V5. he experiment was mainly to pass the modified filter. You can see videos related to the experiment below.
(The firmware download link is at the bottom of this post)



1.Testing CEC Firwmare v1.120 for uBITX v5
It is the video that some experimental firmware is changed and operated in order.

Below is the spectrum of MP3 extracted from the above image.
You can also boost the reception of your Spectrum app on your cell phone. (Using IF Shift function)


I have found that the above spectrum can improve performance a little more.

2.Change filter for V5
I changed one of the boards used for the experiment to V5.

11.052 X-tal and 68p Capacitor


Remove existing parts


Replace with new IF filter




2.Testing CEC Firwmare v1.121 (New Firmware)  for uBITX v5
(The firmware download link is at the bottom of this post)
After changing the filter for V5, verify the performance with the instrument.

Generated a signal of 7.2Mhz at -45dB. The signal passes through the uBITX filter and is converted to speech and then back into the instrument.

Upload the experiment video below. You can check it conveniently in the video.

USB MODE
Stock firmware




CEC V1.121





LSB MODE
Stock firmware





CEC V1.121





Test Video



3.Firmware Download Link
Firmware CEC v1.121 for uBITX V5
https://drive.google.com/open?id=1JA3YNNuZ6Izyb8Hc1nNC69R2DXaC7g5m

I will release it as a major version if the problem does not occur with this firmware.

V3, V4 users do not need to upload this firmware. This firmware has been modified so that the existing V3 and V4 can be applied to V5.

After the beta version is finished, V3, V4, and V5 will be managed from one source as before.


4.conclusion
This has been improved through limited experimentation. Maybe you can not feel it big. So I recommend the IF-Shift function.
When you look at the spectrum with your cell phone, you can feel where your uBITX passes through the filter.
Below is the first post I added to uBITX with the IF-Shift function with the advice of my great friend a year ago.
http://www.hamskey.com/2018/03/test-and-explain-for-if-shift-function.html
http://www.hamskey.com/2018/04/improve-ubitx-receive-performance-by.html


Thanks for reading

Ian KD8CEC

Comments

  1. I do not know exactly because I do not have 7 ", but I think if you change the ID, you can use uBITX without changing the firmware.

    Let me write some Check List.
    1.Which version of uBITX firmware did you upload? For Nextion LCD, you must upload firmware that ends in _NX.hex or _NXS.hex.

    2.Did you buy a new Nextion LCD? Or was it used for other purposes? The default communication speed of Nextion LCD is 9600. Sometimes the LCD used for other purposes may change speed.
    Put a line of baud = 9600 at the top of the preinitialize Event on the px page, and the speed will change to 9600.

    Ian KD8CEC

    ReplyDelete
  2. Dear Ian,
    I have just finished installing a Nextion Display on my V5 Bitx, with your latest firmware. Oddly enough, I can't access the Setup using the push button. Wen I press to access it, the software goes back to homepage, without displaying the options This is a shame as I need to adjust the BFO. Do you have any idea of what's going on?
    Thanks for all the great work!
    Pierre F4ARM

    ReplyDelete
    Replies
    1. Pierre
      What is the firmware name (***. Hex) and Nextion GUI file name (***. tft) uploaded?
      Did you need to adjust the BFO after loading the CEC firmware? If uBITX Memory Manager is available, please backup the uBITX configuration file and send it to me (.btx)

      Ian KD8CEC

      Delete
  3. A follow up on my uBitx. Firmware version is UBITXV5_CEC_V1.122_NX.hex and the GUI is ubtix_35.tft V3. The BFO was already off before I uploaded your firmware, as far as I can tell. I have tried to connect with uBitx manager, but I can't seem to read anything from the transceievr and I keep getting an error message. I must admit I am a bit lost...

    ReplyDelete
    Replies
    1. I recommend that you first check whether the firmware was uploaded properly. Was the firmware uploaded normally? The firmware upload and uBITX Manager use the same serial port.

      CEC firmware supports most LCDs as well as Nextion LCDs. You can upload the firmware for the 16x02 LCD that was included when you purchased uBITX for testing.

      It does not modify any hardware of uBITX but uploads firmware only, so you can check if firmware upload is good.
      Ian KD8CEC

      Delete
    2. Hi Ian,
      I finally managed to get everything working after reloading the firmware a couple of times. That is weird, but now, I have a fully functional uBitx.

      All the best!
      Pierre

      Delete
  4. Hi Ian, I'm new to using Nextion displays. Do i need to load firmware into both the arduino board and the Nextion display to use your firmware with the Ubitx kit? What link will show me the complete procedure please? Thanks W3BUW

    ReplyDelete
    Replies
    1. W3BUW

      The uBITX CEC firmware supports most LCDs. Before using Nextion LCD, please try CEC firmware for 16x02 LCD first without H/W Modify.

      Please refer to the link below for how to install Nextion LCD in uBITX.
      http://www.hamskey.com/2018/06/ubitx-with-nextion-lcd-cec-firmware.html

      Ian KD8CEC

      Delete
  5. Does uBITX's other functions work?
    Then it will not be a problem.
    i2c Scan is for users who have I2C LCD or DIY custom uBITX.

    ReplyDelete
  6. I got the rig all loaded with firmware CEC V1.122 with a 2.8 display and it works well. Except it is hard to figure out how to calibrate. Display is off 1800 as it was with the factory firmware. Have done lots of reading but everyone of the versions have a different calibration scheme it seems. Any advice greatly appreciated as it is a wonderful rig. I have made 7 contacts with it so far with lots of amazing reports.
    Thanks
    Larry

    ReplyDelete
    Replies
    1. Larry
      Sorry for the late feedback.

      Most versions can be calibrated in uBITX Manager. off 1800 means the frequency is shifted?
      If you send me your uBITX file (uBITX Mananger -> Read from uBITX -> Save to File), I will review the Calibration file.

      Ian KD8CEC

      Delete
  7. Dear Ian

    Many thanks for your hard work and fantastic software, I have assembled two uBitx
    (V3 & V4) and installed your software on both. Recently I have built a Bitx 40 for portable use is it possible to adapt your software for the Bitx. The reason I ask is that the latest version of the Bitx uses the same Raduino with 16 pin angled header as the uBitx so your software possible with an encoder would transform this radio.

    Regards Mike

    ReplyDelete
    Replies
    1. Mike

      I bought Bitx a few months ago, but I have not assembled yet.
      Bitx and uBITX use the same radino, but the circuit structure is slightly different.
      It seems to be usable by modifying the frequency control part.
      A friend I met in uBITX groups a year ago saw an example of using CEC Firmware in BITX.
      Ian KD8CEC

      Delete
  8. thanks for asll the work - its great.
    I have uBitx v3, v4 and v5 boards and genuine nextion 2.4, 5 & 7 inch displays.
    I have firmware file ubitxv5_cec_v1.22_nx.hex and the matching hmi files.
    on the v5 board the 2.4" works fine - great interface but too small for my old eyes and fat fingers however the 5" & 7" are stuck in the 2.4 resolution size.
    any hints as to solve would be approciated.

    cheers Matt

    ReplyDelete
    Replies
    1. I am having the same problem with a 3.5". I works great but it is in 2.4 in screen size.

      Delete
    2. i did see some other tft files bbut they are not for the enhanced version - i.e. they error on config load to the screen. still hunting but cant seem to find any to dowwnload.

      Delete
  9. Is the source posted somewhere? I need to make a couple of modifications so that it works with my radio.

    ReplyDelete
    Replies
    1. Thank you for your comment
      The source is in github.
      I'm going to post the source after finishing the beta test period today.

      Ian KD8CEC

      Delete
  10. Dr. Ian, hello.. new ubitx builder here. I have a v5 board and downloaded the latest software, v1.121 but i do not know where to find the nextion 3.5 tft file for my NX4832K035_011 display. please advise!

    ReplyDelete
    Replies
    1. https://ubitx.net/2018/07/16/nextion-3-2-and-3-5-display-firmware/

      Delete
    2. Note that the letter "K" in the model number... NX4832K035_011 signifies that the display is of type "ENHANCED". so, make SURE you get the "ENHANCED" 3.5" display file loaded or it won't work.

      Delete
    3. Kelly

      Is not the answer too late?
      You can download the firmware that ends with K as mentioned in the comment above.
      If you can not find it again, please write again.
      Ian KD8CEC

      Delete
  11. I notice when WWSPR beacon si TX the TX indicatoir does not come on - it stays at RX
    great work on the rest. Love it.

    ReplyDelete
    Replies
    1. uBITX Version 5?

      I will test it again before releasing the firmware today.

      Ian KD8CEC

      Delete
  12. Vicky
    Thank for your comment
    Ian KD8CEC

    ReplyDelete
  13. We follow an efficient and collaborative approach to make sure we provide our clients with the best bodyguard services in residential securityLondon at affordable costs. We've worked with many clients, and one thing we've realized is that their cooperation has contributed to a lot to our success.

    ReplyDelete
  14. Its a cozy delight reading your claim.Its full of aspire i am looking for and i lionize to claim a comment that "The content material of your proclaim is incredible" extremely good accomplish.
    thank you for the update, especially first-rate site.. Download Overwatch Crack

    ReplyDelete
  15. Hey, i am a new user your site was too good.
    IDM Crack

    ReplyDelete
  16. exceptional call I could at some point or another to thank you for the endeavors you have made in prearranging this enticing and proficient article.
    https://martinaonp199.postach.io/post/how-to-explain-facebook-marketing-courses-to-your-boss

    ReplyDelete
  17. Awesome post, Thank you for always sharing this blog. Lanai Screen repair Sarasota, FL

    ReplyDelete
  18. slotauto รวมเว็บไซต์ สล็อต ไว้ภายในค่าย สล็อตGalaxy มีเกมออนไลน์มากยิ่งกว่า 200 เกมส์ ให้ท่านเลือกเล่น pg slot ท่านจะได้รับความสนุกสนานร่าเริงจำนวนมาก มีต้นแบบที่เล่นง่าย

    ReplyDelete

Post a Comment

Popular posts from this blog

Introduction to UV-K5 HF Fullband receive version 0.3

Introduction to UV-K5 HF Fullband receive Version 0.3 This is an introduction to UV-K5 HF full-band reception firmware 0.3HF using SI4732-A10. This version is released separately from the existing UV-K5 CEC firmware version. because space is needed to store a large PATCH file to use SI4732-A10's SSB. 0.3HF added several functions to use SSB for shortwave radio and amateur radio.

Release CEC Firmware v1.200 for uBITX All version(include V2, V3, V4, V5)

Release CEC Firmware v1.200 for uBITX All Version (include v2, v3, v4, v5) I did the firmware work for v5 when uBITX V5 was released, but I release it now. I received the feedback from a thankful beta tester and tested it myself by converting my uBITX v3 to v5 but I was not sure. I ordered the uBITX V5 and delivered the correct uBITX V5, so I made a little more fine-tuning. If you use V2, V3, V4, you do not need to update this firmware.

Introducing UV-K5 Version 0.1P (CW)

  Introducing UV-K5 Version 0.1P (CW Mode) CW-related functions have been added to version 0.1P. The spectrum function has been removed but is maintained in the source code. Later, when the source code is distributed, you can activate it and use it if necessary. This version is for testing purposes only. It will be redistributed as the stable version 0.2 in approximately 1-2 weeks. If you don't want to beta test, you can wait a week or two and download 0.2